04.12
bird
INSTALLATION
Installation of bed-dawn simulator is simple and trouble-free, but requires, as all units subject to a supply voltage, the observance of certain rules:
- Connect the system to an electric (220V 50Hz), consistent with current standards, equipped with earth.
- Do not take powers above those recommended for each outlet <2> <3>.
- Do not open, whatever the reason, the container of the simulator. Inspections and repairs must be performed by qualified personnel only.
- Protect the simulator from moisture and heat. The simulator can not be used outdoors.
- Do not apply neon lights in the decision for filament lamps (taken <3>).
- Replace the fuse with one type having the same characteristics as that provided by the manufacturer.
- Do not place the simulator in confined spaces in order to be able to dissipate the heat that emanates light.
The product has a warranty of 18 months from the date of purchase, provided the installation conditions outlined above are met.
TIE-IN
- Set the simulator RG3000 vertically oriented window, using calipers that are on the bottom of the container.
- Connect the incandescent lamps taking <3> (600W maximum).
- Connect the neon lights in decision <2> (1000W max).
- Connect the simulator to the power line (220 Volts 50 Hz).
- Interuptor turn the ON / OFF <1>.
- Press the button RESET
- Wait at least 1 minute before you start programming
After that, you can proceed with the instructions provided in paragraphs 4 - 5 - 6 and so on. Meanwhile, regardless of your program, the program will start automatically and pre dawn light up the neon lights.
SET TIMES
- Press the button <9> (the LED signal lights).
- Press the button <5> or <6> to set the current time (display 24 hours).
- Press the button <9> (the indicator light turns off signaling).
SETTING EARLY DAWN
- Press the button <10> (the LED signal lights).
- Press the button <5> or <6> to setting the desired time (24 hours display).
- Press the button <10> (the indicator light turns off signaling).
REGLADE EARLY SUNSET
- Press the button <11> (the LED signal lights).
- Press the button <5> or <6> to setting the desired time (24 hours display).
- Press the button <11> (the indicator light turns off signaling).
Points 4 - 5 - 6 can be changed at any time by simply pressing the appropriate button <9> <10> <11> and by acting on the push <5> <6>.
DURATION OF THE DAWN AND SUNSET
Using the graduated knob <13>, it is possible to set the time of dawn and sunset.
- 0 = 2 minutes of dawn and sunset.
- 5 = 30 minutes of sunrise and sunset.
- 10 = 60 minutes of sunrise and sunset.
For intermediate values, use of the interim figures.
SETTING NIGHT LIGHT
It is possible to use incandescent lamps used to generate the dawn and sunset as night light (moonlight effect). This is useful when you do not want the lighting does not drop to zero (total darkness) overnight.
The user can adjust the light intensity from '0 '(night light off) and '10' (intensity 75% of the incandescent lamp used), graduated through the handle <15>. It is possible to set and see this function only during night hours (between the end of a sunset and the beginning of a blade).
If, for whatever reason, you must enter during the night hours, in breeding, without panicking the birds, press the button <7>, night inspection. This will result in a rapid dawn of approximately 1.5 minutes on incandescent lamps. Then, the neon light up and remain lit for the time of your arrest in animal husbandry. When you exit, press the button again <7>, and the lights go down with a pre-determined about 20 minutes.
During the day, the pusher <7> is automatically disabled by the system.
LIGHTING CONTROL
The handle graded <14> is used to adjust the sensor.
Position '0 'is at least the sensor's sensitivity. Therefore, the neon lights (only during the time between the end of a blade and the beginning of a bed) will be lit (LED off).
If the natural light that filters through the windows at certain times of the day is sufficient, you can adjust the sensor to save a few hours of artificial lighting by addressing the following way. When you consider sufficient sunlight, turn the handle graded <14> slowly from '0 'to larger numbers until such time as the neon lights go out (LED display on). Now make shadows with your hand on the sensor: the neon lights will light up (LED off). By removing the hand of the sensor, turn off the neon lights (LED signaling lights). If it was not the case, turn the handle graded <14> a little to the larger numbers and try again.
The setting is thus completed, the neon lights turn on automatically when ambient light falls below the programmed on and off automatically when the light reaches or exceeds the programmed threshold.
For a perfect setting, it is essential to the conduct in sunny day, never in cloudy days and being careful not to come between the source (window) and the sensor.
AUTOMATIC EXTENSION AND REDUCTION OF THE DAY
The change in day length in breeding, in addition to the buttons <10> and <11> in manual mode, can also be performed in automatic mode using the button <12> as follows. To extend the day, press the button one time <12>, the green LED lights up, so the day goes on '6 'minutes per day, in other words, the dawn will begin '3' minutes before and bedtime begin '3 'minutes later each day.
The past days to hours of light considered optimal from you again press the button 2 times <12>, the LED will be off and the hours of light will remain stable. When the breeding season ends and you wish to decrease the length of days, press the button 2 times <12>, the yellow LED stays on and the days begin to decline by '6 'minutes per day, of other words, the dawn begins '3 'minutes after sunset and '3' minutes before each day. After hours of light with desired, press again, once the button <12>, the yellow LED turns off and the hours will be stable.
You can see the display and change (if any) at any time, the time of the early morning and early to bed, respectively, by pressing buttons <10> and <11>.
Variation in the duration (+6 / -6) AUTOMATIC EXTENSION AND REDUCTION OF THE DAY
- Upon completion of the program as stated in the instruction manual, the timer is set to 6 / -6.
- To set +6 / -6, hold down the <12> until both lights come on at the same time.
- The display shows the indication that is 03.00 that day longer or shorter than 3 minutes at dawn and 3 minutes at sunset (6 minutes total).
- Press <5> (-) or <6> (+> until you reach the desired minutes.
Example 1: If you press the <5> (-) until you reach the indicated 02.00 the day lengthens or shortens to 2 minutes at the beginning and 2 minutes at sunset (4 minutes total).
Example 2: If you press <6> (+) until you reach the indicated 3.20 day longer or shorter than 3 minutes at dawn and 3 minutes at sunset ( 6 minutes total) for 2 days and 4 minutes at dawn and 4 minutes at sunset (8 minutes total) for one day, and this will be repeated during the following days.
The programmer has memorized the second and after a minute he reached forward to programming.
Press <12> to turn off the lights, while the current time reappears on the screen.
Press <12> to select 6 / -6 logically the day lengthens or shortens the number of minutes you have selected.
PERIOD PHOTO
It is possible to enter the public photos that period when we do not use the functions 6 / -6 and vice versa.
PHOTO TIME function is very useful to be able to vary (extend, shorten or transfer) the hours of light allowing us to create or follow pre-existing tables. With our system you can at any time of the year into a useful table to facilitate the reproduction or the singing and the birds will have no stress from abrupt changes in hours of illumination, which as we know can sometimes be fatal.
Example: If you set the timer on a morning at 9 am and sunset at 18 hours, and you want in 90 days or dawn at 7 am and sunset at 22 hours, it will be scheduler which will divide the hours minutes or seconds that vary daily so that after 90 days dawn and sunset coincide with those desired by the breeder.
How to?
- Press Photo Period <16> (LED lit), the LED will light day at the same time and appear on the screen indicating 0001.
- Press <5> or <6> and set the days on the screen you want.
- Press OK <17> to confirm the arrival dawn hours LED will turn on automatically and the screen will appear indicating 0001, press <5> or <6> until the desired setting for dawn after the days previously been made, press OK <17> to confirm the hours led sunset arrival will turn on automatically and the screen will appear indicating 2222, and pressing the < 5> or <6> until the time chosen for the sun after days previously been made, press OK <17> to confirm.
The current time will reappear on the screen and only the LED will remain lit picture period.
After the day set at the beginning of the programming, photo function automatically interlocking period, however, having settled dawn and sunset on the desired values.
You can leave at any time period picture function manually by pressing the <16> and turning off the LED, the hours of dawn and the sunset to stop those violations of the time of interlocking manual.
NOTES
In case of lack of power-supply, the simulator does not lose any programmed function for 24 hours. Once electricity is restored, he returned immediately with a blade about 1.5 minutes fast, to turn immediately neon (this happens only during the phase logically day).
Using the push RESET you can cancel all previous programs so that they can do it again.
During the period of non-use of the controller, leave the system plugged into the outlet and on, unplugging the catch of neon and incandescent only (power consumption, in this case, the programmer will be insignificant and preserve the battery reserve).
Unit Size: 21 x 10 x 6 cm.
MANUFACTURER
BESSER ELECTRONIK
Via Brescia, 13
26029 Soncino (CR)
Tel: 0374 83395
Fax: 0374 83395
Posted in: breeding
0 komentar:
Posting Komentar